店铺已关闭且信息已无效
店铺已关闭且信息已无效
详细说明
插头相机插头数码相机插头数码插头数码相机配件插头
fpc连接器fpc插座fpc连接座fpc插座连接器
ffc连接器ffc插座ffc插座连接器ffc插头座
产 品 规 格 书
product specification
【1】适用范围scope
本规格书适用于:0.5间距柔性扁平电缆连接器(有锁式)
this specification covers the 0.5mm pitch fpc/ffc connectors(series locking)
【2】产品名称及型号product name and part number
产品名称product name 产品型号part number
ffc/fpc扁平电缆连接器
【3】定格ratings
项目 item 规 格 requirement
大容许电压
rated voltage(max) 50v [ac/dc(有效值virtual value)50hz]
大容许电流
rated current(max) 0.4a
使用温度范围
ambient temperature range -25℃~+85℃
【4】性能performance
4.1电气性能electrical performance
项目item 条 件 test condition 规格requirement
4.1.1 接触电阻
contact resistance 适合fpc/ffc嵌合;开放电压20mv以下;短路电流10ma的状态下测定。
mate applicable fpc/ffc and measure by dry circuit,20mv max,10ma. ≤20 mωmax
4.1.2
绝缘电阻
insulation resistance 适合fpc/ffc嵌合;相邻端子间或端子与地面间加dc 500v下测定。
mate applicable fpc/ffc and apply 500v dc between adjacent terminal or ground. 500mωmin
4.1.3
耐电压
dielectric 适合fpc/ffc嵌合;相邻端子间或端子与地面间加ac 200v(有效值)历时1分钟下测定。
mate applicable fpc/ffc and apply 200v ac(virtual value)for 1minute between adjacent terminal or ground. 无击穿现象
no breakdown
4.2机械性能mechanical performance
项目item 条 件 test condition 规格requirement
4.2.1 锁紧力及拔出力
locking and withdrawal force适合0.3mm厚的ffc;用每分钟25±3mm的速度;平行地插入、锁紧、拔出。
insert and extract applicable ffc at the speed rate of 25±3mm/minute. 锁紧力locking
1.96*n (n) max
拔出力withdrawal
0.49*n (n) min
4.2.2 端子保持力
terminal /housing retention force 以用每分钟25±3mm的速度平行向外拉
pull the terminal at the speed rate of 25±3mm per minute 3.92n min
4.3环境和其他性能environmental performance and others
项目item 条 件 test condition 规格requirement
4.3.1 重复插拔
repeated insertion and withdrawal 无通电状态;以10次/分钟的速度插拔20次
insertion and withdrawal actuator up to 20 cycles at the speed rate of less than 10 cycles/minute 接触抵抗
contact resistance 60 mωmax
4.3.2 温度上升
temperature rise 适合fpc/ffc嵌合;大容许电流通电,温度测定。(ul 498)
carrying rated current load.(ul 498) 温度上升
temperature rise 30℃max
项目item 条 件 test condition 规格requirement
4.3.3
耐振动性
vibration dc 1ma通电状态下;嵌合轴沿xyz三个方向振动;振幅1.5mm;频率10-55-10hz/分;历时2小时
amplitude:1.5mmp-p
sweep time:10-55-10hz in 1 minute
duration:2 hours in each x.y.z. axes 外观
appearance 无损坏
no damage接触抵抗
contact resistance 60 mωmax瞬断
discontinuity 1 ms max.
4.3.4
耐冲击性
shock dc 1ma通电状态下;嵌合轴沿相互垂直的6个方向;以490m/s2{50g}冲击;各3次
490m/s2{50g},3 strokes in each x.y.z. axes. 外观
appearance 无损坏
no damage瞬断
discontinuity 1 ms max.
4.3.5
耐热性
heat
resistance 适合fpc/ffc嵌合;85±2℃的空气中;放置96小时;再回到室温中放置1-2小时
85±2℃,96 hour外观
appearance 无损坏
no damage接触抵抗
contact resistance 60 mωmax
4.3.6
耐寒性
cold
resistance 适合fpc/ffc嵌合;-40±2℃的空气中;放置96小时;再回到室温中放置1-2小时
-40±2℃,96 hour 外观
appearance 无损坏
no damage接触抵抗
contact resistance 60 mωmax
4.3.7
耐湿性
humidity
适合fpc/ffc嵌合;40±2℃、相对湿度90-95%的空气中;放置96小时;再回到室温中0.5小时内测定
temperature:40±2℃
relative humidity:90-95%
duration:96 hours 外观
appearance 无损坏
no damage
接触抵抗
contact resistance 60 mωmax
耐电压
dielectric
strength 必须满足4.1.3
must meet 4.1.3绝缘抵抗
insulation resistance 20 mω min
4.3.8
温度循环
temperature
cycling 适合fpc/ffc嵌合;-55±3℃30分钟;常温常湿10-15分钟;85±2℃30分钟;常温常湿10-15分钟,循环5次。
5 cycles of:
a) -55±3℃ 30 minutes
b) 85±2℃ 30 minutes 外观
appearance 无损坏
no damage接触抵抗
contact resistance 60 mωmax
项目item 条 件 test condition 规格requirement
4.3.9
耐盐雾性
salt spray 适合fpc/ffc嵌合;35±2℃、5±1%的盐水喷雾48小时;试验后常温水洗;再室温干燥。
48±4 hours exposure to a salt spray from the 5±1% solution at 35±2℃. 外观
appearance 无损坏、腐蚀
no damage接触抵抗
contact resistance 60 mωmax
4.3.10
耐亚酸
so2 gas 适合fpc/ffc嵌合;40±2℃、50±5ppm的亚酸中放置24小时
24 hours exposure to 50±5ppm. so2 gas at 40±2℃. 接触抵抗
contact resistance 60 mωmax
4.3.11
耐性
nh3 gas 适合fpc/ffc嵌合;浓度为28%的水容器中;放置40分钟。
40 minutes exposure to nh3 gas evaporating from 28% ammonia solution 外观
appearance 无损坏
no damage 接触抵抗
contact resistance 60 mωmax
4.3.12
可焊性
solder ability 端子前端基准面0.2mm处浸入235±5℃的锡槽中;历时2±0.5 sec。
soldering time:2±0.5 sec.
soldering temperature:235±5℃
0.2 mmfrom terminal tip 沾敷性
solder wetting 沾敷面积95%以上
4.3.13
耐焊接热
resistance to
soldering heat 端子前端基准面0.2mm处浸入260±5℃的锡槽中;历时5±0.5 sec。
soldering time:5±0.5 sec.
soldering temperature:260±5℃
0.2 mmfrom terminal tip 外观
appearance 无损坏、变形
no damage
reference standard
:参考单位reference unit
【5】外观形状、寸法及材质product shape,dimensions and materials
图面参照refer to the drawing.
名称 name 材质 materials
主体main body lcp(本色) ul 94v-0
锁扣housing lock lcp(黑色) ul 94v-0
端子sit uip磷青铜 phosphor bronze
焊片contact 磷青铜 phosphor bronze
备注remark 金属表面镀锡
线长 : 40-400(mm) ;
形状 : 条形 ;
读卡类型 : micro ;
支持卡数 : 单卡 ;
接口类型 : zif ;
应用范围 : 显示屏 ;
种类 : ffc/fpc ;
型号 : fpc连接器.fpc0.5mm/1.0mm/1.25mm.全国专业连接器制造商.产品全.质量保证 ;
品牌 : 国产 ;
企业产品
相关分类
插头、插座
AC-DC连接器
端子(terminal)
电脑连接器
电缆连接器
USB连接器
PCB连接器
电源连接器
线束、连接线、端子线
汽车连接器
通讯连接器
手机连接器
端子排、接线排(条)
闭端子(压线帽)
端子盘
屏线、斑马纸
传感器连接器
鳄鱼夹、弹簧夹、电瓶夹
端子台、接线柱(头)
光纤端子
接线座、接线板
扬声器(喇叭)连接器
排针、排母、排线
转接头
电池连接器
HDMI连接器
水晶头
AV连接器
IC连接器
汇流排(总线)
针座、插针
简牛、牛角
S-video端子
DispalyPort
板对线连接器
WAFER连接器
显示屏连接器
1394连接器
BNC连接器
DVI连接器
SCSI连接器
卡座(读卡器连接器)
护套
射频同轴(RF)连接器
LED连接器
线对线连接器
DC-DC连接器
RJ45连接器
D-SUB(VGA)端子
IDC连接器
板对板连接器
SATA、ATA连接器
光纤连接器
胶壳(housing)
ZIF连接器
PCI连接器
DIN(大、中、小)
FFC、FPC连接器
IPOD连接器
HDR连接器
背板连接器
PLCC连接器
端子接插件
航空连接器